1. Thank you to all those who submitted to the Federal Inquiry into E-Cigarettes for making your story count in the fight to legalise nicotine in Australia. Submissions may be viewed HERE.
    Dismiss Notice

Coil Porn - show us your winds

Discussion in 'Rebuildable Atomisers' started by DaveJ, Jun 3, 2015.

  1. Subohmies

    Subohmies Member

    Joined:
    Jun 13, 2015
    That hole! Is that what chowder sent you?
     
  2. DogMan

    DogMan Yes

    Joined:
    Jun 3, 2015
    Location:
    S/E Melbourne
    no, i pif that one
     
  3. Subohmies

    Subohmies Member

    Joined:
    Jun 13, 2015
    I will sent it back if that's how it look like...lol
     
  4. Tara

    Tara Member

    Joined:
    Jun 3, 2015
    Location:
    Perth
    Browny, DaveJ and DogMan like this.
  5. dnar

    dnar Member

    Joined:
    Jun 6, 2015
  6. Northerner

    Northerner Member

    Joined:
    Jun 12, 2015
    Yesterdays build on my new raptor. Deck is very marquis style.

    [​IMG]
     
    Catweazle likes this.
  7. James

    James Senior Member

    Joined:
    Jun 13, 2015
    Location:
    Hobart, Tasmania
    After viewing this thread, I pulled the pin on giving claptons a shot, I used this guide and oh my it is so easy! This guy is a genius.

    24gauge core with 32gauge wrapped around it

    Results (iPhone camera y u so bad):
    [​IMG]
     
    Last edited: Jun 16, 2015
    subyXV and Catweazle like this.
  8. James

    James Senior Member

    Joined:
    Jun 13, 2015
    Location:
    Hobart, Tasmania
    First build of Friday a.k.a Rebuild day

    Got a bit creative
    24ga clapton'd with 32ga twisted with twisted o.5 (I think) Ribbon wire. Comes out at 0.175 ohms

    [​IMG]
     
    Catweazle likes this.
  9. Danyel

    Danyel Member

    Joined:
    Jun 14, 2015
    Location:
    Geelong
    Well it's not exactly coil porn, nor is it very exciting however, it is my latest Ni200 coil, 11 wraps of 26G on a 5mm bit, dialing in at .15ohm. As you can see it fits in the Magma with room to spare, allows for plenty of cotton, and apart from a slight ramp up time, 1-2 seconds, its by far the best TC build I've tried yet. Flavour is juicy and producing plenty of the grey matter.

    [​IMG]
     
  10. James

    James Senior Member

    Joined:
    Jun 13, 2015
    Location:
    Hobart, Tasmania
    Couple more, I love Fridays

    [​IMG]
     
  11. Big O

    Big O Member

    Joined:
    Jun 12, 2015
    Location:
    Morayfield, QLD
    My Dodgy coils, 22G @ 0.3 ohms.
    [​IMG]
     
    soda and Catweazle like this.
  12. Danyel

    Danyel Member

    Joined:
    Jun 14, 2015
    Location:
    Geelong
    Dual zippers, 2 strand 26G twisted & 7 wraps @ 2.5mm

    [​IMG]
     
    Kingpin, soda, Big O and 2 others like this.
  13. Big O

    Big O Member

    Joined:
    Jun 12, 2015
    Location:
    Morayfield, QLD
    [​IMG]
    Todays build.
     
    Catweazle likes this.
  14. dnar

    dnar Member

    Joined:
    Jun 6, 2015
    I found it best to have the majority of cotton inside the coil with thin ends to lead the juice to the heat. Large blogs outside the coils hold fluid right there.
     
  15. pcan68

    pcan68 Member Vendor

    Joined:
    Jun 14, 2015
    Location:
    Caboolture Qld
    On the Troll RDA Ni200 coil, 11 wraps of 30G on a 5mm bit .32 ohm at 30W and the flavour is really good. Still learning how to get the coil really neat and spaced consistently, the Ni is so fiddly.

    [​IMG]
    [​IMG]
     
    Catweazle and DogMan like this.
  16. DogMan

    DogMan Yes

    Joined:
    Jun 3, 2015
    Location:
    S/E Melbourne
    as long as it works paul
     
    Browny, Sean, Danyel and 1 other person like this.
  17. Danyel

    Danyel Member

    Joined:
    Jun 14, 2015
    Location:
    Geelong
    An oldie but a goodie was this coil. 2 strands of 24G kanthal twisted and wrapped 7 times over a 2.5mm bit and split at the bottom to each of the negative screws. Dialed in at .5 ohm. Was a bitch to wick but worth the trouble if you dont mind the ramp up time.

    [​IMG]
     
    Browny and Catweazle like this.
  18. Darkhorse

    Darkhorse Member

    Joined:
    Jun 10, 2015
    [​IMG]

    I put another coil in but this is my favourite shot of this build.
     
    Browny, Catweazle, Danyel and 2 others like this.
  19. James

    James Senior Member

    Joined:
    Jun 13, 2015
    Location:
    Hobart, Tasmania
    I'm going to give that a shot next Darkhorse, looks awesome. What gauges did you use?

    but first I need more wire :c
     
  20. DaveJ

    DaveJ I Vape

    Joined:
    Jun 2, 2015
    Location:
    Perth, Western Australia
    You sir, have skills.

    One day........ Na, who am I kidding? :)
     

Share This Page