1. Thank you to all those who submitted to the Federal Inquiry into E-Cigarettes for making your story count in the fight to legalise nicotine in Australia. Submissions may be viewed HERE.
    Dismiss Notice

Coil Porn - show us your winds

Discussion in 'Rebuildable Atomisers' started by DaveJ, Jun 3, 2015.

  1. Darkhorse

    Darkhorse Member

    Joined:
    Jun 10, 2015
    I put the specs in my wire knitting thread :) 22g nichrome, 24g nichrome and 30g kanthal
     
    DaveJ likes this.
  2. laurie9300

    laurie9300 Photoshop Whore

    Joined:
    Jun 2, 2015
    Location:
    Western Sydney, Australia
    24G : 6 wraps on 3mm : 0.4 ohms : DarkHorse RDA by Chowderhead

    [​IMG]
     
  3. Danyel

    Danyel Member

    Joined:
    Jun 14, 2015
    Location:
    Geelong
    It's not 'Coil Porn', however, it is my latest build. 17 x 3mm wraps of 26G Ni 200 dialing in at .14ohm in a Derringer, wicked with KGD, and soaking in Bobas. A little slow on the ramp up time but producing a juicy & flavoursome vape set at 350F & 20 watts.

    [​IMG]

    [​IMG]
     
    Last edited: Jul 3, 2015
    Jerry Hatrick, margyb and Catweazle like this.
  4. James

    James Senior Member

    Joined:
    Jun 13, 2015
    Location:
    Hobart, Tasmania
    das a lot of wraps
     
    margyb likes this.
  5. Danyel

    Danyel Member

    Joined:
    Jun 14, 2015
    Location:
    Geelong
    It is a lot. I'd normally twist together... oh wait, who am I kidding, I dont have a 'normal' method, each coil I build is as varied as the next. I just like to tinker and experiment as I go.
     
    James likes this.
  6. laurie9300

    laurie9300 Photoshop Whore

    Joined:
    Jun 2, 2015
    Location:
    Western Sydney, Australia
    Well the lure of all this untried juice I've got lying around has prompted me to do something I've been meaning to do for a while now.

    Twisted 32g, Ni200, 10 wraps on 3mm, 0.28Ω single in the magma, great flavour!

    [​IMG]

    These higher ohm nickel builds are great!
     
  7. James

    James Senior Member

    Joined:
    Jun 13, 2015
    Location:
    Hobart, Tasmania
    Something new, 7 wrap 22ga spaced on a dotmod petri clone

    [​IMG]

    Edit: Just wicked it.... oh my god so much flavour, warm, dense.... this is my new flavour build for sure. Vaping it at 60w
     
    Last edited: Jul 25, 2015
    Jerry Hatrick, Danyel, Browny and 4 others like this.
  8. laurie9300

    laurie9300 Photoshop Whore

    Joined:
    Jun 2, 2015
    Location:
    Western Sydney, Australia
    Man you could hold up a bridge with that!^^^^^^^^
     
    Catweazle and James like this.
  9. Hoffer

    Hoffer Member

    Joined:
    Jun 12, 2015
    Some great coils here.

    Does anyone know anyone in Australia that sells pre built clapton or twisted coils?
     
  10. Big O

    Big O Member

    Joined:
    Jun 12, 2015
    Location:
    Morayfield, QLD
    What is that atty good sir?
     
  11. Subohmies

    Subohmies Member

    Joined:
    Jun 13, 2015
    VE carry them
     
  12. James

    James Senior Member

    Joined:
    Jun 13, 2015
    Location:
    Hobart, Tasmania
    A Dotmod Petri clone

    I'd link to one, but that'd be naughty
     
    Last edited: Jul 28, 2015
  13. rotten

    rotten Senior Member

    Joined:
    Jun 15, 2015
    Location:
    riverland
    First double barrell for a long time. 30g, 12 wraps each, 2mm, 1.2 ohm somehow. Not like Laurie with 0.5. So not overly tight but it does the job
    [​IMG]
    [​IMG]
     
    Jerry Hatrick, Browny and laurie9300 like this.
  14. rotten

    rotten Senior Member

    Joined:
    Jun 15, 2015
    Location:
    riverland
    So I thought I would try mesh in the taifun.
    Its got a cotton feeder wick, 26 g, 10 wraps, 18mm x 40mm needle hollow mesh wick.
    Vaping like a champ
    [​IMG]
     
    Jerry Hatrick, Browny, Danyel and 2 others like this.
  15. Northerner

    Northerner Member

    Joined:
    Jun 12, 2015
    twisted ribbon and 32, 1 ohm build.

    [​IMG]
     
    Jerry Hatrick, Browny, Danyel and 2 others like this.
  16. rotten

    rotten Senior Member

    Joined:
    Jun 15, 2015
    Location:
    riverland
    Nice. I can't get ribbon to work for me
     
  17. Northerner

    Northerner Member

    Joined:
    Jun 12, 2015
    It's twisted with normal kanthal... That way I get the extra surface area but not the ribbon nightmare :)
     
    rotten likes this.
  18. rotten

    rotten Senior Member

    Joined:
    Jun 15, 2015
    Location:
    riverland
    Hmmm, I have 0.3 ribbon and 32 kanthal.
    Cheers
     
  19. Northerner

    Northerner Member

    Joined:
    Jun 12, 2015
    20mm top hole atty, comes in at 1 ohm. Great vape... smooth and warm.
    [​IMG]
     
    Last edited: Aug 9, 2015
    Jerry Hatrick, Browny and Danyel like this.
  20. Snidely_Whiplash

    Snidely_Whiplash New Member

    Joined:
    Jun 13, 2015
    Location:
    Yagoona, NSW
    ick ?!?
    you've gotta ell in your atty
    (is it slimy)
     
    James likes this.

Share This Page